GE Profile dishwashers in Los Angeles
GE Profile dishwashers sit in a particular kind of Los Angeles kitchen. We pull them out of remodeled Craftsman kitchens in Los Feliz, beach houses along the Malibu coast, and condo galleys in Marina del Rey, and after 24 years the intake notes repeat themselves. A machine that fills and hums but never drains. A control board that drops dead mid cycle and leaves the racks full. Start and status lights blinking in a pattern the manual never explains, with the cycle stuck at the same minute mark. These are the three complaints that fill our GE Profile dishwasher repair schedule, and each one has a short list of causes.
Guessing is expensive here because three different failures produce the same dead machine, and a board swapped on a hunch costs more than the visit that would have ruled it out. We diagnose first and quote before any work begins, a $95 diagnostic, waived with your repair. You may expect the figure to climb once the toe panel comes off. It does not. The price we name standing at your sink is the price on the invoice. Repairs use genuine OEM parts, most are finished same or next day, and every one carries the 3 Year Onyx Warranty.
What actually fails
The failure points we see most on GE Profile machines.
Machine control board behind the door console
The board sequencing fill, wash, and drain fails with heat and moisture cycling. Symptoms range from a machine that will not start to a relay stuck closed, running the pump endlessly. We test inputs and outputs before condemning the board.
Sump drain pump and outlet path
Standing water after the final cycle usually traces to the drain pump or the path it feeds. Glass shards jam the impeller, and the air gap or disposer knockout blocks flow. We clear the route and replace the pump only when it failed.
Cycle status lights and fault logic
Blinking Start or Clean lights with a cycle frozen at one point are the machine flagging a fault it cannot recover from. The pattern points to a subsystem, not a part. We read it, verify the suspect component, and reset after the cause is fixed.
Door latch and interlock microswitch
A dishwasher that goes dark the moment you close the door often has a worn latch microswitch rather than an electrical fault. The strike no longer seats, the interlock never closes, and nothing runs. Latch assemblies are stocked on the truck for single visit replacement.
Send it to us
Tell us what stopped working.
Four fields, no account, no obligation. We reply during business hours, 7am to 7pm, and the $95 diagnostic is waived with your repair.
Why Onyx
The care your kitchen deserves.
Factory trained specialists
Vetted, uniformed technicians certified across every major luxury appliance brand.
Genuine OEM parts
Only genuine components for the brand we are servicing, sourced direct. No aftermarket substitutes.
White glove home protection
Floors, stone, and cabinetry are draped and protected before a single panel comes off.
$95 diagnostic, waived with your repair
One flat diagnostic visit. Go ahead with the repair and the diagnostic costs you nothing.
Concierge scheduling
One point of contact, arrival windows kept, and updates by text or call, whichever you prefer.
Licensed and insured
Bonded and fully insured on every visit. Documentation ready on request.
Questions, answered
Before you call.
Do you repair GE Profile dishwashers?
Yes, constantly. Onyx Appliance Service is an independent company, not affiliated with or authorized by GE Appliances. Factory trained technicians handle the patterns these machines repeat, boards that die mid cycle, pumps that leave water behind, and lights that blink while the cycle never moves.
What do the flashing lights on a GE Profile dishwasher mean?
Reading the blink pattern is the first step of our diagnostic. The lights signal a fault the machine cannot clear, often a stuck cycle, a drain problem, or a failing board. Rather than quoting from the pattern alone, we test the flagged component and price the actual repair.
What does a GE Profile dishwasher repair cost?
GE Profile owners get a flat answer from us. The visit starts with a $95 diagnostic that is waived with your repair, and you receive an exact quote before any work begins. One Quote. One Price. Guaranteed Repair. No Supplemental Estimates.
Do you use genuine GE Profile parts?
Every part we fit is genuine OEM, matched to your model and serial number, never an aftermarket substitute. The common parts, boards, pumps, latches, and fill valves, ride on the truck, which is why most GE Profile repairs finish in a single visit.
Is the repair covered by a warranty?
Before we leave, the coverage goes on paper. Every Profile repair carries the 3 Year Onyx Warranty on both parts and labor, in writing at the time of service. If the fault returns inside that window, we make it right.
The Onyx guarantee
The 3 Year Onyx Warranty, parts and labor, in writing.
A $95 diagnostic, waived with your repair, and 24 years on luxury appliances behind every visit.
More GE Profile repairs
Another GE Profile machine giving you trouble.
See every GE Profile repair we handle across Los Angeles & Southern California.
Same day service · Los Angeles & Southern California
Your peace of mind is one call away.
One number, and it is handled, from diagnosis to a kitchen that simply works again.
$95 diagnostic, waived with your repair.