GE Profile refrigerators in Los Angeles
GE Profile French door refrigerators dominate the remodeled kitchens of Sierra Madre, Agoura Hills, and Calabasas, most of them with the ice maker hung inside the left door. That door mounted ice maker is where the trouble usually starts. We see auger motors that stop turning, chute flaps that stick open and sweat, and fill tubes that freeze into a solid plug. When a Profile stops cooling outright, the compressor is rarely the culprit. Across 24 years of refrigerator work, the main control and inverter boards have produced far more warm boxes than the compressors they drive.
Guessing on this machine gets expensive fast, because a new compressor and a new inverter board sit at very different price points and the symptoms overlap almost completely. So we test before we talk numbers, a $95 diagnostic, waived with your repair, and the figure we quote is the figure you pay. You may assume the price will climb once the back panel comes off. It will not. We arrive same or next day, carry genuine OEM parts for the common board and ice maker failures, and back the work with a 3 Year Onyx Warranty.
What actually fails
What breaks on a GE Profile, in order of likelihood.
Main control and inverter board
A Profile that reads warm in both compartments usually has a board problem, not a compressor problem. The main control stops commanding the inverter, or the inverter stops driving the compressor, and the machine falls silent. We test both boards before condemning either.
Door mounted ice maker
Profile French door models hang the ice maker inside the left door, where temperature swings hit it hardest. When cubes stop dropping we check the door harness, the motor module, and the seal around the ice compartment before any part is replaced.
Dispenser auger and chute flap
Press the paddle and nothing turns, that is the auger motor. Ice welded into a single block, or a chute that drips, that is the flap stuck open. Both faults live in the dispenser assembly and both are serviced on site.
Fill tube freeze up at the door ice maker
A slow trickle from the fill valve freezes inside the tube until a plug of ice blocks every fill cycle that follows. We thaw the line, then correct the pressure or valve fault that built the plug so it does not return.
Fresh food evaporator fan motor
The fan behind the rear panel moves cold air from the evaporator to both compartments. When its bearings wear you hear a chirp that stops when the door opens, and the fresh food side warms while the freezer stays cold.
Defrost heater and thermistor circuit
Frost that creeps over the rear panel points to a defrost circuit that never fires. We test the heater, the thermistor, and the wiring between them, because replacing one blindly leaves the ice sheet ready to grow back within weeks.
Send it to us
Tell us what stopped working.
Four fields, no account, no obligation. We reply during business hours, 7am to 7pm, and the $95 diagnostic is waived with your repair.
Why Onyx
The care your kitchen deserves.
Factory trained specialists
Vetted, uniformed technicians certified across every major luxury appliance brand.
Genuine OEM parts
Only genuine components for the brand we are servicing, sourced direct. No aftermarket substitutes.
White glove home protection
Floors, stone, and cabinetry are draped and protected before a single panel comes off.
$95 diagnostic, waived with your repair
One flat diagnostic visit. Go ahead with the repair and the diagnostic costs you nothing.
Concierge scheduling
One point of contact, arrival windows kept, and updates by text or call, whichever you prefer.
Licensed and insured
Bonded and fully insured on every visit. Documentation ready on request.
Questions, answered
Before you call.
Do you repair GE Profile refrigerators?
Yes, daily. Onyx Appliance Service is an independent company, not affiliated with or authorized by GE Appliances. Our techs handle the faults Profile owners actually report, boards that mimic a dead compressor, ice makers mounted in the door that quit, and dispenser augers that stop turning.
My GE Profile refrigerator is not cooling. Is it always the compressor?
We test the electronics first, and that order matters. On most warm Profiles the main control board or the compressor inverter has failed while the compressor itself is healthy. Board level repair costs a fraction of a sealed system job, so we confirm before we condemn.
What does a GE Profile refrigerator repair cost?
GE Profile pricing starts the same way every time, with a $95 diagnostic that is waived with your repair. Once we identify the fault you get an exact quote before any work begins. One Quote. One Price. Guaranteed Repair. No Supplemental Estimates.
Do you use genuine GE Profile parts?
Genuine OEM components only, matched to your model and serial number before we order, never aftermarket substitutes. The boards, ice maker modules, and valves that fail most often ride on the truck already, which is why most Profile repairs finish in a single visit.
Is the repair covered by a warranty?
Before the truck leaves your driveway, the coverage is already in writing. Every repair carries the 3 Year Onyx Warranty on both parts and labor, handed to you at the time of service, so a repeat of the same fault costs you nothing.
The Onyx guarantee
The 3 Year Onyx Warranty, parts and labor, in writing.
A $95 diagnostic, waived with your repair, and 24 years on luxury appliances behind every visit.
More GE Profile repairs
Same badge, different machine, same standard.
See every GE Profile repair we handle across Los Angeles & Southern California.
Same day service · Los Angeles & Southern California
Your peace of mind is one call away.
One number, and it is handled, from diagnosis to a kitchen that simply works again.
$95 diagnostic, waived with your repair.