GE Profile dryers in Los Angeles
GE Profile dryers in this part of Los Angeles tend to live in tight quarters. In Century City condos they sit stacked in hallway closets, in Culver City and Hollywood they share converted garages and second floor laundry nooks with long vent runs behind the wall. The calls we log follow 2 patterns. Thermistor faults skew the temperature reading, so the dryer either overshoots or shuts the heat off early and runs cool. And the heat pump and hybrid models produce no heat while the drum keeps turning, a fault that looks minor and is not. After 24 years in Los Angeles laundry rooms, we read these machines quickly.
Guessing is expensive on this machine because a no heat complaint has 5 plausible causes and none of the parts are cheap. Hybrid models hide a refrigeration loop behind the drum, so swapping the obvious part usually fixes nothing. We diagnose first, then hand you an exact quote before any work begins, with a $95 diagnostic, waived with your repair. You likely expect that number to climb once the rear panel comes off, and it does not. We install genuine OEM parts, run same or next day, and back the work with a 3 Year Onyx Warranty.
What actually fails
The faults that stop a GE Profile dryer.
Exhaust outlet thermistor
The thermistor tells the control what the exhaust air is doing. When its resistance drifts, the dryer trims heat too early, runs cool, and stretches every cycle. We test the sensor against a known temperature curve and replace it with the correct OEM part.
Heat pump drying module
Hybrid Profile dryers dry with a sealed refrigeration circuit instead of a glowing element. When the module quits, the drum spins, the cycle counts down, and the load stays cold and damp. We test the circuit before naming any part.
Blower wheel and airflow path
Lint packs the blower wheel and the duct behind the wall, and airflow collapses. The dryer then overheats, cycles the heat off, and takes 2 passes to finish towels. We clear the whole path and verify airflow before closing the machine up.
Drum belt and idler tension arm
A worn belt squeals on startup, then snaps and leaves the motor humming with a drum that never turns. The idler that keeps it tight wears first. We replace both together so the fix holds instead of returning in 6 months.
Send it to us
Tell us what stopped working.
Four fields, no account, no obligation. We reply during business hours, 7am to 7pm, and the $95 diagnostic is waived with your repair.
Why Onyx
The care your kitchen deserves.
Factory trained specialists
Vetted, uniformed technicians certified across every major luxury appliance brand.
Genuine OEM parts
Only genuine components for the brand we are servicing, sourced direct. No aftermarket substitutes.
White glove home protection
Floors, stone, and cabinetry are draped and protected before a single panel comes off.
$95 diagnostic, waived with your repair
One flat diagnostic visit. Go ahead with the repair and the diagnostic costs you nothing.
Concierge scheduling
One point of contact, arrival windows kept, and updates by text or call, whichever you prefer.
Licensed and insured
Bonded and fully insured on every visit. Documentation ready on request.
Questions, answered
Before you call.
Do you repair GE Profile dryers?
Yes, every configuration, electric, gas fired, hybrid, and combo washer dryer units included. The 2 faults we log most are thermistor drift that skews drying temperature and hybrid machines that tumble without heating. Onyx Appliance Service is an independent company, not affiliated with or authorized by GE Appliances.
Why does my GE Profile heat pump dryer take so long to finish a load?
First we check the simple things, a packed lint screen housing and a crushed or overlong vent. If airflow is clean, attention turns to the thermistor and the sealed drying module, since a weak refrigeration circuit dries at low temperature and stretches the cycle. Diagnosis names the true cause.
What does a GE Profile dryer repair cost?
GE Profile dryers get a $95 diagnostic, waived with your repair, and you receive an exact quote before any work begins. One Quote. One Price. Guaranteed Repair. No Supplemental Estimates. The figure covers the whole job, whatever the teardown reveals.
Do you use genuine GE Profile parts?
Genuine OEM only, matched to your model and serial number before anything is ordered or installed. Aftermarket substitutes never go into your machine. Thermistors, belts, idlers, and blower wheels ride on the truck, which is why most Profile dryer repairs finish in a single visit.
Is the repair covered by a warranty?
Before the technician leaves, you get the coverage in writing. Every repair carries the 3 Year Onyx Warranty on both parts and labor, so if the same fault returns inside 3 years, the fix is on us. The paperwork is handed over at the time of service.
The Onyx guarantee
The 3 Year Onyx Warranty, parts and labor, in writing.
A $95 diagnostic, waived with your repair, and 24 years on luxury appliances behind every visit.
More GE Profile repairs
More GE Profile equipment under the same roof?
See every GE Profile repair we handle across Los Angeles & Southern California.
Same day service · Los Angeles & Southern California
Your peace of mind is one call away.
One number, and it is handled, from diagnosis to a kitchen that simply works again.
$95 diagnostic, waived with your repair.