Maytag washers in Los Angeles
Maytag washers do the heavy lifting in family houses across Tarzana, Woodland Hills, and Chatsworth, where a single machine may run 10 loads a week between kids, sports gear, and dogs. After 24 years working on these units, we see the same failures on repeat. Bravos XL top loaders stop spinning when the rotor position sensor drifts and the control throws F51. Lid lock errors strand a full drum of water. Maxima front loaders grind down their bearings and flag Sud and F8 E4. Older Centennial and Atlantis machines wear their drive blocks and agitator dogs until the agitator just swirls. Drain pumps choke on coins and grit.
Guessing is expensive on these machines because the symptoms overlap. A Bravos XL that will not spin can be a rotor position sensor, a failed lid lock, or a jammed drain pump, and the parts prices are nowhere near each other. So we never quote from a symptom. A factory trained technician runs the diagnostics, opens the machine, and confirms the failed part before naming a number. The visit is a $95 diagnostic, waived with your repair. We fit genuine OEM parts, arrive same or next day across the Valley, and back every repair with a 3 Year Onyx Warranty.
What actually fails
The six ways a Maytag washer gives up.
Bravos XL rotor position sensor and F51
The rotor position sensor on the Bravos XL drive reports basket speed to the control. When it drifts, the washer stirs, stalls, and throws F51 instead of spinning. We test the sensor and harness, then replace the failed part and verify a full spin.
Lid lock assembly
A failing lid lock leaves the control convinced the lid is open, so the cycle refuses to start or halts with a locked light blinking over a drum full of water. We check the striker, the lock assembly, and the wiring before replacing anything.
Maxima bearing failure, Sud and F8 E4
A Maxima front loader with a roar on spin has bearing wear, and the drag often surfaces as Sud or F8 E4 on the display. We measure drum play and tell you honestly whether a bearing job or a replacement machine is the smarter spend.
Drain pump and filter
Coins, hair pins, and sock fragments work past the basket and lodge in the drain pump, so the washer holds water at the end of a cycle. We clear the pump, check the impeller for chipped vanes, and replace the pump when it is damaged.
Centennial and Atlantis drive block and agitator dogs
On older Centennial and Atlantis top loaders the splined drive block and the agitator dogs wear smooth, so the motor runs while the agitator barely swirls the load. Both parts are inexpensive, and replacing them returns the wash action the machine had when new.
Neptune wax motor door lock and control board
Legacy Neptune front loaders fail at the wax motor door lock, which then stresses the control board until relays stick. If your Neptune will not unlock or start, we assess both parts together, because replacing one without checking the other invites a repeat call.
Tell us what it is doing
Tell us what the Maytag washer is doing.
Four fields and we call you back, same or next day, between 7am and 7pm.
Why Onyx
The care your kitchen deserves.
Factory trained specialists
Vetted, uniformed technicians certified across every major luxury appliance brand.
Genuine OEM parts
Only genuine components for the brand we are servicing, sourced direct. No aftermarket substitutes.
White glove home protection
Floors, stone, and cabinetry are draped and protected before a single panel comes off.
$95 diagnostic, waived with your repair
One flat diagnostic visit. Go ahead with the repair and the diagnostic costs you nothing.
Concierge scheduling
One point of contact, arrival windows kept, and updates by text or call, whichever you prefer.
Licensed and insured
Bonded and fully insured on every visit. Documentation ready on request.
Questions, answered
Before you call.
Do you repair Maytag washers?
Yes, both top load and front load models, every week. Onyx Appliance Service is an independent company, not affiliated with or authorized by Maytag or Whirlpool Corporation. Our technicians handle the Bravos XL rotor position sensor and F51 fault, lid lock errors, and Maxima bearing failures daily.
Why does my Maytag Bravos XL stop before the spin cycle?
Start by watching what the machine does after the drain. If it pauses, clicks, and shuts down with F51, the rotor position sensor has stopped reporting basket speed and the control aborts the spin. The fix is a sensor replacement, and we confirm it with a full loaded test spin.
What does a Maytag washer repair cost?
Maytag repairs start with a $95 diagnostic, waived with your repair, so the inspection costs nothing once you approve the work. You receive an exact quote before any work begins. One Quote. One Price. Guaranteed Repair. No Supplemental Estimates. The number we name is the number you pay.
Do you use genuine Maytag parts?
Every part we fit is genuine OEM, matched to your model and serial number before we order or pull it from stock. No aftermarket substitutes. The trucks carry common Maytag washer parts, including rotor position sensors, lid locks, and drain pumps, so most repairs finish in a single visit.
Is the repair covered by a warranty?
Before the technician leaves, you receive the coverage in writing at the time of service. Every Maytag washer repair carries the 3 Year Onyx Warranty on both parts and labor. If the same failure returns inside that window, we come back and make it right at no charge.
The Onyx guarantee
The 3 Year Onyx Warranty, parts and labor, in writing.
A $95 diagnostic, waived with your repair, and 24 years on luxury appliances behind every visit.
More Maytag repairs
Same Maytag badge, different machine giving trouble.
See every Maytag repair we handle across Los Angeles & Southern California.
Same day service · Los Angeles & Southern California
Your peace of mind is one call away.
One number, and it is handled, from diagnosis to a kitchen that simply works again.
$95 diagnostic, waived with your repair.